Skip to content

HACCP Plan for a Flour Mill: Raw Grain, Metal, Sifting

A HACCP plan for a small flour mill: why flour is a raw food, grain at receiving, magnets and sifters, metal at bagging, allergen changeovers, a worksheet.

By Koa Sterling. Product specialist at TaroStack and small business owner. Yes, I am a real human, and I actually sit in front of a computer and write these articles. Reviewed November 21, 2026 · 6 min read

A flour mill's plan starts from a fact that surprises people: flour is a raw food. Grain grows in a field, where it can pick up Salmonella and harmful E. coli, and FDA says plainly that grinding it into flour doesn't kill them. A mill has no cooking step. So it can't make the hazard go away, and the plan says so: the control for bacteria is the label, telling the buyer to cook it, and the baker's oven. What the mill does control is everything else. Mycotoxins and moisture in the grain it accepts. Stones, metal and wire, taken out by cleaning, magnets, sifters and a check at bagging. And cross-contact, where one mill grinds wheat and other grains. Below is a plan for a made-up stone mill, a day's log, and a worksheet.

The short version

  • Flour is raw. Milling doesn't kill bacteria, and the bag should say to cook before eating.
  • Accept grain on a document: a mycotoxin test or certificate, and your own moisture reading.
  • Clean the grain: screens, air, a destoner, a magnet.
  • Look at the sifter screens every day of milling.
  • A metal check at bagging is the last control.
  • One mill for several grains needs a changeover clean and a flush.
  • TaroStack records which load of grain went into which bags. More below.

Raw flour

FDA's page on handling flour safely puts it in two sentences: "Flour is a raw food," and "Processing raw grains into flour does not kill harmful bacteria." It counts 168 known illnesses since 2009 in outbreaks tied to raw flour and products made with it, such as cake mix and cookie dough. Cooking is the only way to be sure.

For a mill that means three things. The hazard analysis lists bacteria as a hazard the mill doesn't eliminate. The bag carries a line such as "Raw flour: cook or bake before eating." And a customer who wants flour for something that won't be cooked, such as edible cookie dough, needs heat-treated flour, which is a different product with a validated process of its own.

The hazards, step by step

Step Hazard Control
Receiving grain Bacteria from the field; mycotoxins; stones, metal Approved growers; a test or certificate; moisture checked
Grain storage Mold in damp grain; pests Moisture and temperature watched; pest control
Cleaning Stones, metal, other seeds Screens, aspirator, destoner, magnet
Milling Bacteria not removed; metal from the mill The label; magnet and sifter after the mill
Sifting Metal, sifter wire, insects Screens inspected each day
Changeover Wheat carried into another grain's flour Clean and flush between grains
Bagging Metal Detector or final magnet; a lot on every bag

The controls

Under FDA's preventive controls rule a mill's plan has process controls, allergen controls, sanitation controls and a supply-chain program, as its hazard analysis requires.

Control Limit Checked If it's missed
CCP 1 Metal at bagging Detector rejecting each test piece, or the final magnet in place and clean Start, every hour, end Bags since the last good check held and passed again
Supply chain: grain A test or certificate inside the buyer's specification Every load, before unloading Load refused, or held and tested
Process: sifter Screens whole Every day of milling Flour since the last good check sifted again
Allergen: changeover Mill, sifter and bagger clean; flush discarded Every change of grain Cleaned and flushed again

Grain. Mycotoxins are made by molds in the field and in storage, and no step in a mill removes them. So they're controlled where the grain is bought: a test result or a certificate for each load, checked against a specification before the truck is unloaded. Moisture is the mill's own reading at the door, because damp grain molds in the bin. The 13.5% in the worksheet is this mill's own limit. The program is in supplier approval program template.

Sifter screens. A sifter takes out what the cleaning missed, until a screen tears. Then it adds wire. Look at every screen each day the mill runs, and look at the tailings, which is where a broken screen shows first.

Changeover. A mill that grinds wheat on Monday and buckwheat or corn on Tuesday carries wheat forward in every corner. Clean, then run a flush of the new grain through and keep that flush out of sale. A "gluten-free" claim needs far more than this: see HACCP plan for gluten-free.

A day's log

Time What Result OK?
7:00 AM Hard red wheat, load 88, moisture 12.4%, limit 13.5% Yes
7:10 AM Metal detector, start of bagging Test pieces rejected Yes
12:00 PM Sifter screens Torn screen on deck 2 NO: act
3:00 PM Metal detector, hourly Test pieces rejected Yes

At noon a screen on the second deck was found torn. The morning's 40 bags were held and sifted again through a new screen, and a piece of wire turned up in the tailings. The daily look found it at 40 bags. A weekly look would have found it at 400, some of them sold.

This is general information, not legal advice. Metal checks are in metal detector CCP, and writing a plan from the start in how to write a HACCP plan.

Get the worksheet

Download the flour mill food safety plan worksheet. Three sheets and a read-me: the hazard analysis from grain to shipping, the plan with its metal, grain, sifter and changeover controls, and a monitoring log that marks a result outside its limit. It's an ordinary Excel file with no macros, and it works in Google Sheets, LibreOffice and Numbers.

Where this stops working

A grower calls: the wheat from one field tested high for a mycotoxin after it was delivered. That load went into a bin with two others. Which milling days drew from that bin, which bags, and which bakeries bought them? The receiving log has the load. The bags have a date. Nothing connects the two.

How TaroStack does it

TaroStack connects a load of grain to the bags it became.

Each load is a lot, with the grower's own lot or field beside yours and its moisture and test result noted.

Each milling run is a batch. It notes which grain lots it used, automatically, and your checks are fields on its record: screens inspected, metal check, initials.

Each run's flour is a lot. Lot labels print with the code, and what ships is recorded by lot.

One report for a lot of grain: which runs used it, which customers got that flour, and what's left. Starting a recall holds it.

Recipes with scrap take bran and screenings into account, so the grain used matches the flour made.

The grower's call Paper logs In TaroStack
Which runs milled that load Unknown The lots on each run
Which bags A date The run's lot
Which bakeries bought them Invoices One report
Flour still in the store Walk the pallets Stock by lot, on hold

TaroStack doesn't test grain or run a metal detector. Recipes, batches, lots and recalls are on every plan, from $9.99 a month (5 recipes) or $39 a month (50 recipes). The first 14 days are free, with no credit card. If you'd like a hand setting up, ask, and we'll do it with you.

Questions people also ask

Is flour a raw food?

Yes. FDA says flour is a raw food and that processing raw grains into flour doesn't kill harmful bacteria such as Salmonella and E. coli. Cooking or baking does.

What are the critical control points in a flour mill?

In this example, the metal check at bagging, with grain acceptance, sifter inspection and changeover cleaning as other preventive controls. A mill has no kill step for bacteria.

How does a mill control bacteria in flour?

It can't remove them without a heat treatment. It buys from approved growers, keeps grain dry, and labels the flour as raw, to be cooked before eating.

Sources

  1. FDA, Handling Flour Safely: What You Need to Know (flour is a raw food; processing raw grains into flour does not kill harmful bacteria; cooking is the only way to be sure) · read November 21, 2026
  2. 21 CFR 117.135 (preventive controls: process, food allergen, sanitation and supply-chain controls) · read November 21, 2026

We use AI to help with the research for these articles. Every one is read, checked against its sources and edited by Koa before it's published. Spot a mistake? Tell us and we'll fix it and say so. How we write these.

Let’s get your stack in order.

Get TaroStack

Sign up now for your free 14 day trial. No credit card required.