A sanitizer concentration log is a record of test strip readings: each time someone checks the sanitizing solution in the three-compartment sink, the dish machine or the wiping cloth buckets, they write down the reading in parts per million, whether it's in range, and what they did if it wasn't. The check matters because a sanitizer is used within a band. Too weak and it doesn't do its job. Too strong and it's over the limit its label allows. And a solution that was right at seven can be weak by noon. The FDA Food Code says the concentration "shall be accurately determined by using a test kit or other device". The log is how you show it was. Below is a log for a made-up kitchen, what the Food Code sets for each kind of sanitizer, and the template.
The short version
- Test with strips made for your sanitizer: chlorine, quaternary ammonium or iodine.
- Record the date, time, place, reading and initials.
- The range to work to is on the sanitizer's EPA-registered label.
- Test when you make up the solution and through the day, as your health department asks.
- Out of range: remake it, retest, and deal with what was washed in it.
- Write down the action, not just the reading.
- TaroStack isn't a sanitizer log. It keeps the batch and lot records beside it. More below.
An example log
| Date | Time | Where | Sanitizer | Reading | Range | In range | Action taken | Initials |
|---|---|---|---|---|---|---|---|---|
| Nov 16 | 7:15 AM | Three-compartment sink | Chlorine | 75 ppm | 50 to 99 | Yes | KS | |
| Nov 16 | 11:40 AM | Three-compartment sink | Chlorine | 30 ppm | 50 to 99 | NO | Solution remade, retested at 75. Items washed since 10:30 re-sanitized | KS |
| Nov 16 | 7:20 AM | Wiping cloth bucket | Quaternary ammonium | 200 ppm | 150 to 200 | Yes | ML | |
| Nov 16 | 3:00 PM | Wiping cloth bucket | Quaternary ammonium | 100 ppm | 150 to 200 | NO | Bucket changed, retested at 200 | ML |
The ranges in this table are placeholders to show the layout. Yours come from your sanitizer's label.
The second row is the one an inspector reads. The solution had dropped to 30 ppm, and the entry says three things: it was remade, the new solution was tested, and the pans washed in the weak solution were done again. A "NO" with nothing beside it raises more questions than it answers.
What the Food Code sets
The FDA Food Code is a model. Your state or county adopts its own version, so check which one applies to you. Section 4-501.114 of the 2026 edition says a chemical sanitizer is "used in accordance with the EPA registered label use instructions", and then sets conditions by type.
| Sanitizer | What 4-501.114 says |
|---|---|
| Chlorine | A minimum water temperature that depends on the concentration and pH. At 25 to 49 mg/L: 120°F. At 50 to 99 mg/L: 100°F at pH 10 or less, or 75°F at pH 8 or less. At 100 mg/L: 55°F |
| Iodine | Between 12.5 and 25 mg/L, at 68°F or warmer, at pH 5.0 or less unless the manufacturer specifies otherwise |
| Quaternary ammonium | At 75°F or warmer, at the concentration in the manufacturer's use directions, in water of 500 mg/L hardness or less unless the label allows more |
A milligram per liter is the same as a part per million for these solutions, which is why strips read in ppm.
Two more sections are about the testing itself. 4-302.14: "A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided." And 4-501.116: the concentration "shall be accurately determined by using a test kit or other device."
So the Food Code asks for the strips and for the testing. The sections read here don't prescribe a log sheet. Your health department or your food safety plan may ask you to write the readings down. Ask how often.
The upper limit. The label's maximum has a rule behind it. 40 CFR 180.940 lists the chemicals allowed in sanitizing solutions for food-contact surfaces, each with a limit "when ready for use". For one quaternary ammonium compound on the list, the solution "is not to exceed 200 ppm of active quaternary compound". Stronger isn't safer. It's off the label.
How to take a reading
- Use strips for the right chemical. A chlorine strip doesn't read a quaternary ammonium solution.
- Check the strips' expiry date, and keep them dry.
- Dip for the time the strip's instructions give. It differs by brand.
- Compare with the color chart straight away, in good light.
- Write it down before you do anything else.
For chlorine, temperature is part of the answer: a reading of 75 ppm meets the Food Code's table only if the water is warm enough for that concentration.
When it's out of range
| Reading | Do |
|---|---|
| Too low | Remake the solution. Retest. Re-sanitize whatever was washed since the last good reading |
| Too high | Dilute or remake to the label's range. Retest |
| Strip doesn't change | Check the strips: wrong kind, expired or wet. Then test again |
If readings keep falling, look for the cause, such as a dispenser that's out of chemical or dirty water carried into the sanitizer sink. Fixing the cause belongs in the action column too.
Related logs: cleaning log template, dish machine temperature log, temperature log template. All of a kitchen's logs side by side are in log sheet examples.
Get the template
Download the sanitizer concentration log. One sheet and a read-me: type the reading and the range you work to, and the sheet marks each row in range or not. Print it and keep it by the sink with the strips. It's an ordinary Excel file with no macros, and it works in Google Sheets, LibreOffice and Numbers.
Where this stops working
A sanitizer log is a clipboard job, and that's the right tool for it. Where paper lets a kitchen down is the part after the bad reading: "items washed since 10:30". Which items, used for which batch of what? A sanitizer failure at the sink is a question about the food that touched those pans, and the clipboard by the sink knows nothing about the food.
How TaroStack does it
TaroStack doesn't record sanitizer readings. It keeps what was made, so a problem at the sink can be followed to the product.
Each batch is a lot, with the time it was made.
Batch records carry your own checklist fields, so "sanitizer checked" can be a tick on the batch if you want it there.
A lot can be put on hold while you decide what to do.
What ships is recorded by lot, and every lot is traced to the customers that got it.
| The question | Clipboard | In TaroStack |
|---|---|---|
| What was made between 10:30 and 11:40 | Memory | Batches by time |
| Where is that product now | Unknown | The lot's stock, and who got it |
| Can it be held | If you can find it | Hold the lot |
TaroStack isn't a temperature or sanitizer log, and it doesn't replace your test strips. Lots, batches and holds are on every plan, from $9.99 a month (5 recipes) or $39 a month (50 recipes). The first 14 days are free, with no credit card. If you'd like a hand setting up, ask, and we'll do it with you.
