Skip to content

Dish Machine Temperature Log: Wash, Rinse and 160°F

A free dish machine temperature log: wash and final rinse temperatures, the 160°F test at the dish, limits by type of machine, and what to do on a fail.

By Koa Sterling. Product specialist at TaroStack and small business owner. Yes, I am a real human, and I actually sit in front of a computer and write these articles. Reviewed November 21, 2026 · 7 min read

A dish machine that sanitizes with hot water has to do one thing: get the surface of the dish to 160°F. Everything on the log is a way of knowing it did. The gauges on the machine show the wash temperature and the final rinse temperature, which the FDA Food Code sets by type of machine: for most, a rinse of at least 180°F at the manifold and no more than 194°F. But gauges read the water, not the plate, so the code also asks for an irreversible temperature indicator, a test strip or label that changes color at 160°F, run through on a rack. A log sheet records the two gauge readings each meal period and the strip at least daily, and says what was done when one failed. A machine that sanitizes with chemicals is checked differently: wash temperature and a sanitizer test strip. Below are the limits, a log for a made-up kitchen, and a file.

The short version

  • Hot water machines: the dish surface reaches 160°F. Prove it with a test strip.
  • Final rinse 180°F to 194°F for most machines. Read the data plate for yours.
  • Wash temperature by type of machine: 150°F to 165°F.
  • Chemical machines: wash at 120°F or above, sanitizer at its label strength.
  • Read the gauges every meal period, while a rack is running.
  • A fail means stop: rewash, and sanitize another way until it's fixed.

The limits

Hot water sanitizing machines.

Type of machine Wash, at least Final rinse, at least
Stationary rack, single temperature 165°F 165°F
Stationary rack, dual temperature (most door types and undercounters) 150°F 180°F
Single tank, conveyor, dual temperature 160°F 180°F
Multi-tank, conveyor 150°F 180°F

The final rinse is never above 194°F: hotter than that, the water can turn to vapor before it has done its work on the dish. Rinse pressure has to be in the range on the data plate.

The result, at the dish: 160°F at the utensil's surface, measured with an irreversible registering temperature indicator.

Chemical sanitizing machines. Wash at 120°F or above. The sanitizer at the concentration and contact time on its EPA-registered label, checked with a test kit.

By hand, in a sink. Hot water sanitizing means immersion at 171°F or above for at least 30 seconds, which few kitchens can hold. Most use a chemical sanitizer in the third compartment: see three compartment sink requirements.

Your machine's data plate gives its own minimums and they're the ones to put on the log. If the plate is worn away, the maker's manual has them.

What to record

Column How
Date, meal period One row each period
Wash temperature From the gauge, during the wash cycle
Final rinse temperature From the gauge, during the rinse: it only reads true while rinse water is flowing
Rinse pressure From the gauge, if there is one
Test strip at the dish Fix a strip or label to a plate, run it, read it. At least daily
Initials Who read it
Action taken Anything other than "fine"

Read during the cycle. A rinse gauge on an idle machine shows the temperature of water sitting in the pipe. Run a rack and watch.

The strip is the proof. Gauges fail, drift and get stuck. The strip went through the machine and either changed or didn't. Keep the used strips with the log for a week or two, taped to the sheet.

Two days

Date Period Wash Final rinse Strip: 160°F? Check
Nov 16 Breakfast 156°F 184°F Yes OK
Nov 16 Lunch 158°F 183°F Yes OK
Nov 16 Dinner 155°F 182°F Yes OK
Nov 17 Breakfast 154°F 172°F No STOP
Nov 17 Lunch Three-compartment sink Sanitizer strip in range
Nov 17 Dinner 157°F 185°F Yes OK

On the 17th the rinse read 172°F and the strip didn't change. The booster heater had tripped. The machine was taken out of use, the racks washed that period were washed again, and the kitchen used the three-compartment sink with chemical sanitizer until a technician reset the heater at 3:10. A strip was run before the machine went back into service.

That's the whole corrective action, and it's worth writing on the wall beside the machine:

  1. Stop using the machine to sanitize.
  2. Rewash and sanitize everything since the last good reading.
  3. Switch to the sink and a chemical sanitizer, tested.
  4. Call for service.
  5. Run a strip before going back.

Why machines fail

Symptom Usual cause
Rinse low Booster heater off, tripped or scaled up; water heater can't keep up at peak
Wash low Tank heater; machine filled with cold water and not given time
Gauges fine, strip unchanged Clogged rinse nozzles; low pressure; racks overloaded so water can't reach
Chemical machine, strip low Empty sanitizer drum; kinked or perished feed tube

Scale is the slow one. In hard water it coats heater elements and nozzles, and the rinse temperature sinks a degree a month until one day it's 176°F. A log shows the slide before the inspector's strip does.

Whether dishwashing belongs in a HACCP plan: usually it's a prerequisite program, not a control point, and the log is its record. The list of those programs is in prerequisite programs for HACCP. Cleaning of everything else is in cleaning log template, and thermometer checks in thermometer calibration log.

Your state may use an older edition of the Food Code. This is general information, not legal advice. Your health department has the last word.

Get the log

Download the dish machine temperature log. A log with a Check column that compares wash and rinse readings and the strip with your limits, a Limits sheet for your machine's minimums, and a read-me. Print a month of rows and hang it by the machine. It's an ordinary Excel file with no macros, and it works in Google Sheets, LibreOffice and Numbers.

Where this stops working

This log works on paper, and paper by the machine is the right place for it. Where a kitchen's paper stops working is everywhere else: the dish log, the cooler log, the cooling log, the receiving sheet and the date dots are five clipboards, and the food they're about (which soup, made when, from what) isn't on any of them.

How TaroStack does it

TaroStack doesn't replace the sheet by the dish machine. It keeps the records that are about the food.

What you make is a batch, with a lot code and a use-by, and its record notes which lots went into it, automatically.

Readings about the food are fields on the batch record: cooking temperature, the cooling readings, initials.

An alert before a date passes, in the app and by email.

Receiving records the supplier's lot and dates.

Counting on a phone, with no signal in the walk-in.

The record Stays on paper Goes in TaroStack
Dish machine temperatures Yes, by the machine
What was made, when, from what The batch record
What's about to expire An alert
What came in, and its lot The receiving record

TaroStack doesn't read gauges or sanitize anything. Recipes, batches, lots and expiry are on every plan, from $9.99 a month. The first 14 days are free, with no credit card. If you'd like a hand setting up, ask, and we'll do it with you.

Questions people also ask

What temperature should a commercial dishwasher final rinse be?

For most hot water sanitizing machines, at least 180°F at the manifold and no more than 194°F. A stationary rack, single temperature machine needs 165°F. The dish surface must reach 160°F.

How do you test a dish machine?

Read the wash and rinse gauges while a rack is running, and run an irreversible temperature test strip or label through on a dish to confirm the surface reached 160°F.

What do you do if the dish machine isn't hot enough?

Stop using it to sanitize, rewash what went through since the last good reading, sanitize by hand with a tested chemical sanitizer, and call for service.

Sources

  1. FDA Food Code 2026, 4-501.110 (wash solution temperature by type of machine), 4-501.112 (hot water sanitizing rinse: 180°F, or 165°F for a stationary rack single temperature machine; not above 194°F), 4-501.113 (rinse pressure) · read November 20, 2026
  2. FDA Food Code 2026, 4-703.11 (160°F at the utensil surface; chemical contact times), 4-302.13 (irreversible registering temperature indicator), 4-302.14 (sanitizer test kit), 4-501.111 (manual hot water sanitizing at 171°F) · read November 20, 2026

We use AI to help with the research for these articles. Every one is read, checked against its sources and edited by Koa before it's published. Spot a mistake? Tell us and we'll fix it and say so. How we write these.

Let’s get your stack in order.

Get TaroStack

Sign up now for your free 14 day trial. No credit card required.