Skip to content

HACCP Plan for Potato Chips: Fryer, Seasoning, Metal

A HACCP plan for potato chips: allergens in seasonings, metal detection, the fryer, what FDA's acrylamide guidance suggests for chips, and a worksheet.

By Koa Sterling. Product specialist at TaroStack and small business owner. Yes, I am a real human, and I actually sit in front of a computer and write these articles. Reviewed November 21, 2026 · 6 min read

Potato chips are fried at well over 300°F and sold dry, so germs aren't where a chip maker's plan spends its time. The hazards that reach a customer are three. Allergens: the milk in a sour cream and onion or cheese seasoning, carried into a plain chip through a shared tumbler, or put in the wrong bag. Metal: a chip from a slicer blade. And a chemical one that forms in the fryer itself, acrylamide, which FDA has guidance on and no limit for. Under FDA's preventive controls rule the document is called a food safety plan, and its controls are process controls, allergen controls, sanitation controls and supply-chain controls. Below is a plan for a made-up small chip maker with three flavors, a morning's log, and a worksheet.

The short version

  • The allergen is in the seasoning. Run plain first, clean after an allergen flavor.
  • Check the bag film against the flavor at every changeover.
  • Every bag goes through a metal detector that's tested with test pieces.
  • Fry by a written process: oil temperature, time, and a color chart.
  • For acrylamide: chipping potatoes, kept above 43°F, fried at or below 347°F.
  • Lot codes on every bag, and a record of which seasoning lot went in.
  • TaroStack records which seasoning lot went into which run. More below.

The hazards, step by step

Step Hazard Control
Receiving potatoes High sugars that raise acrylamide; stones Chipping varieties; stored above 43°F; a fry test
Receiving seasonings Milk in a blend; a blend that changed Specification and label checked for each lot
Slicing Metal from blades Blade checks; metal detector later
Frying Pathogens from raw potatoes; acrylamide Oil temperature and time by the process
Seasoning Milk carried into a plain chip Plain first; clean after an allergen flavor
Metal detection Metal Every bag through a working detector
Bagging Wrong film: an allergen not declared Film checked at every changeover

Allergens

Sea salt chips contain potatoes, oil and salt. Sour cream and onion chips contain milk. If both go through one seasoning tumbler and one conveyor, the order of the day matters more than anything else in the plant: plain first, allergen flavors last, a full clean before the next plain run. Someone other than the cleaner looks at the tumbler and signs before it starts again.

The second allergen control is the film. Three flavors in bags that differ by a color band will be mixed up sooner or later. At every changeover and every new roll, the packer reads the film against the run sheet. A plain chip in a sour cream bag is a quality complaint. A sour cream chip in a plain bag is a recall. The wider program is in allergen control plan template.

Metal

Slicer blades are thin, run fast, and are changed often. Count the blades in and out at each change and look at the edges. Then every sealed bag passes through a metal detector that's checked with test pieces at the start, every hour, at each flavor change and at the end. If a check fails, everything since the last good check is held and passed again. The details are in metal detector CCP.

The fryer, and acrylamide

Frying is the kill step for anything on a raw potato, and at chip temperatures that isn't in doubt. What the fryer adds is acrylamide, which forms when sugars and an amino acid in the potato react at high heat.

FDA's guidance on acrylamide is advice, not a rule. It says so, and it sets no maximum or action level. For sliced potato chips it suggests:

Where What the guidance suggests
The potato Varieties low in reducing sugars. Chip makers' own association advises against Russets
Storage Avoid cold, which sweetens potatoes. Trade groups recommend above 43°F for long storage of chipping potatoes
The slice Thinner slices may lower acrylamide in chips
The fryer Higher temperature and longer time raise it, most at the very end as the chip dries. Some makers set fryers at 347°F or below
The finished chip A slightly higher moisture target, 1.3% to 1.5%, and a lighter color

This maker's process puts those into numbers of its own: oil at or below 347°F, a color chart at the fryer exit, and moisture measured each run. A fry test on each load of potatoes shows the color it will give before a full batch is made. Darker chips are the sign of more acrylamide and of more sugar in the potato.

A morning's log

Time What Reading Limit OK?
7:00 Fryer oil, sea salt chips 342°F 347°F or below Yes
7:30 Fryer oil, sea salt chips 356°F 347°F or below NO: act
9:10 Fryer oil, sea salt chips 340°F 347°F or below Yes
11:00 Fryer oil, sour cream and onion 343°F 347°F or below Yes

At 7:30 the oil was nine degrees over. The thermostat was drifting. Chips made since 7:00 were held, found darker than the chart, sorted by color and sold as seconds. That was the maker's own decision under its own target: nothing in the guidance required it. The sour cream and onion run came last, after the plain chips were bagged.

This is general information, not legal advice. Writing a plan from the start is in how to write a HACCP plan, and the business side in potato chips business plan.

Get the worksheet

Download the potato chip food safety plan worksheet. Three sheets and a read-me: the hazard analysis from potatoes to bagging, the plan with its metal, frying and allergen controls, and a monitoring log that marks a reading outside its limit. It's an ordinary Excel file with no macros, and it works in Google Sheets, LibreOffice and Numbers.

Where this stops working

The seasoning supplier emails: one lot of the sour cream and onion blend contains an undeclared ingredient. Which runs used that lot, which bags were they, and where did those cases go? The changeover log says the tumbler was clean. It doesn't say which bag of seasoning was open.

How TaroStack does it

TaroStack records which lots went into each run and where the run went.

Receiving records each seasoning lot and the supplier's own lot number beside yours.

Each flavor is a recipe. Record a run and its potatoes, oil and seasoning come off stock. The run notes which lots it used, automatically.

Your checks are fields on the batch record: oil temperature, color, changeover signed.

One report for a lot: which runs used that seasoning, which customers got those cases, and what's left. Starting a recall holds it.

Allergens on Growth. With allergen tracking on, a batch can't start if its label leaves out an allergen its ingredients contain.

The supplier's email Paper logs In TaroStack
Which runs used that seasoning lot Unknown The lots on each run
Where those cases went Invoices One report
What's still in the warehouse Walk the racks Stock by lot, on hold
A label missing milk Read every film The batch won't start

TaroStack doesn't run the metal detector, measure acrylamide or write your food safety plan. Recipes, batches, lots and recalls are on every plan, from $9.99 a month (5 recipes) or $39 a month (50 recipes, with allergen tracking). The first 14 days are free, with no credit card. If you'd like a hand setting up, ask, and we'll do it with you.

Questions people also ask

What are the critical control points for potato chips?

Usually metal detection, with frying as a process control and allergen controls at seasoning changeover and bagging. Which steps you call critical depends on your own hazard analysis.

Not from FDA. Its guidance on acrylamide in foods is nonbinding and sets no maximum or action level. It suggests ways to lower it.

How do you reduce acrylamide in potato chips?

FDA's guidance suggests chipping varieties low in sugars, storing potatoes above cold temperatures, thinner slices, lower fryer temperatures and a slightly higher finished moisture.

Sources

  1. FDA, Guidance for Industry: Acrylamide in Foods (nonbinding; no maximum or action level; potato chips: varieties, storage above cold temperatures, slice thickness, fryer temperature and moisture endpoint) · read November 21, 2026
  2. 21 CFR 117.135 (preventive controls: process, food allergen, sanitation and supply-chain controls) · read November 21, 2026

We use AI to help with the research for these articles. Every one is read, checked against its sources and edited by Koa before it's published. Spot a mistake? Tell us and we'll fix it and say so. How we write these.

Let’s get your stack in order.

Get TaroStack

Sign up now for your free 14 day trial. No credit card required.