A preventive control plan is the written plan that shows how your food is kept safe and correctly labelled. The CFIA's guide builds it in five steps: assemble a team, make sure the premises meet the regulations, analyze the hazards and set the controls, set the measures for labelling and packaging, and assemble the documents. Below is each step filled in for a 14-person bakery in Ontario that ships bread to Quebec. It's an example to adapt, not a plan to copy: your own hazard analysis decides your controls.
The short version
- Section 89 of the SFCR says what the plan contains; the CFIA's guide and templates show how to write it.
- Start with the premises (sections 50 to 81), then the hazards, then the controls.
- Critical control points come out of your hazard analysis, not out of an example.
- The plan also covers labelling, net quantity and packaging, the consumer protection part.
- Traceability, recalls and complaints are separate SFCR requirements, outside section 89.
- TaroStack keeps the records the plan says you'll keep, beside the batches they belong to. More at the end.
This is general information, not legal advice. Your CFIA inspector has the last word on what applies to you.
Who needs one
Every SFC licence holder, for the activities on its licence, unless an exemption applies. Under $100,000 in food sales, many foods are exempt: bread is, jam and cheese aren't. The exemption, explained. This bakery's food sales are over $100,000, so it needs one.
Step 1: the team
The bakery names three people: the owner, the production manager and the shift lead who does the morning checks. The CFIA's guide asks for people who know food safety and the practical side of the operation. For the hazard analysis, it says you may use a trade or professional association or a consultant.
Step 2: the premises
The CFIA's establishment checklist walks through sections 50 to 81 of the SFCR: the building, water, equipment, cleaning and sanitation, pest prevention, staff hygiene, transport, and so on. For each, the bakery writes what it does, how often and who does it.
| Area | What the bakery does | How often | Who |
|---|---|---|---|
| Cleaning | Mixers, benches and slicer cleaned to a written procedure | End of each shift | Shift lead |
| Pests | Contracted pest company checks bait stations | Monthly | Owner |
| Staff hygiene | Handwashing, hairnets, no jewelry; illness reported before the shift | Daily | Production manager |
| Water | Municipal supply; annual test of the tap at the mixer | Yearly | Owner |
These are the basics. Many hazards are controlled here, before any critical control point.
Step 3: the hazards and the controls
The product and the process
Product: dark rye bread, sliced, in 680 g bags. Ingredients: rye flour, wheat flour, water, salt, yeast, caraway. Allergens: wheat. Made on a line that also makes sesame buns. Shelf life: 5 days at room temperature. Sold to grocers and cafés in Ontario and Quebec, eaten by the general public.
Process: receive, store, weigh, mix, ferment, divide and shape, proof, bake, cool, slice, bag, label, store, ship.
The hazard analysis
For each ingredient and step, the bakery asks what could go wrong, how likely and how bad, and what controls it:
| Step | Hazard | Type | Controlled by |
|---|---|---|---|
| Receiving flour | Foreign matter, pests | Physical, biological | Supplier approval; sifting at weighing |
| Weighing caraway | Sesame on shared scoops | Allergen | Separate scoops by color; sesame weighed last |
| Bake | Pathogens from raw ingredients survive | Biological | Bake to a set time and temperature |
| Cool and slice | Recontamination after baking | Biological | Cleaning of the cooling racks and slicer |
| Slice | Metal from the slicer blades | Physical | Blade check at start and end of shift; metal detector |
| Bag and label | Sesame bread in a rye bag, or a label missing an allergen | Allergen | Label check at line start and each product change |
The critical control points
The bakery decides two of these are critical control points: steps where control is essential and there's no later step to catch a failure. Yours may differ.
| CCP | Critical limit | Monitoring | Corrective action |
|---|---|---|---|
| Metal detection after slicing | Test pieces detected at every check | Test at start, every 2 hours, at end; record | Hold everything since the last good check; re-run it through the detector; find the cause |
| Label check at bagging | The bag's label matches the product in it, allergens included | Check at line start and every product change; record | Hold everything since the last good check; relabel or destroy; find the cause |
Verification
Each week the production manager reviews the CCP records and signs them. Every month the metal detector is tested by someone other than the operator. Once a year the team reviews the whole plan, and after any change of product, supplier or equipment.
Section 89(1)(c)(vii) asks for the documents that show the plan is being carried out, and section 89(2) says each is kept two years from the day it was made. What to keep, and how long.
Step 4: labelling, net quantity and packaging
The plan also describes how the bakery meets the consumer protection rules. That means the label (the common name, the ingredients and allergens, net quantity, the best-before date, its name and address, and a lot code), the packaging, and the net quantity:
- Each new label is checked against the recipe by the owner before it's printed.
- Ten bags per lot are weighed at packing against the 680 g declared.
- Labels from the printer are checked against the approved version before use.
Step 5: assemble the documents
The plan is the documents from steps 1 to 4, plus the records they produce: cleaning sheets, pest reports, CCP logs, verification sign-offs. Keep the plan current, and keep the records two years.
What isn't in the plan
The CFIA's templates don't cover traceability, recalls or complaints. They're separate requirements of the SFCR, and an inspector checks them on their own:
- Traceability records, section 90
- A recall procedure and a yearly simulation, section 84
- A complaints procedure, section 83
Where this stops working
A preventive control plan is written once a year and filled in every day. The daily part is where it goes wrong: CCP logs on a clipboard that a busy shift skips, a metal detector check written at the end of the day from memory, a label check that doesn't say which lot it covered. When a CCP fails, the corrective action needs to know which lots were made since the last good check, and paper doesn't always say.
How TaroStack does it
TaroStack doesn't write your plan. It keeps the records your plan says you'll keep, on the batches they belong to.
Printable batch-record forms carry your own checklist fields and sign-off, so a metal detector check or a label check goes on the batch it covers. Each batch has its lot code, records which ingredient lots went into it, and prints lot labels. So when a check fails, "everything since the last good check" is a list of lots, and holding them is one step. Any lot opens a trace to its ingredients and its customers.
The two people your recall procedure names are kept in settings, and complaints are recorded against their lot.
Lots, holds, recalls and batch records are on every TaroStack plan, from $9.99 a month; a bakery where three people record batches would be on Growth, at $39. It's free for 14 days. If you'd like a hand setting up, ask, and we'll do it with you.
