Dry aging is beef held uncovered in cold, moving air for weeks, until the outside dries to a crust and the inside turns tender. The first question a restaurant or butcher shop has to answer isn't about meat. It's whether the health department wants a variance. The FDA Food Code doesn't name dry aging anywhere. Its list of processes that need a variance ends with "another method that is determined by the regulatory authority to require a variance" (3-502.11(G)), which leaves the decision to your inspector. So ask before you buy a chamber, and be ready to show a written plan. That plan has three working parts: the chamber, the days, and the trim. Below is one for a made-up butcher shop, four days of its log, and a worksheet.
The short version
- Ask your health department first whether dry aging needs a variance where you are.
- Age in a chamber used for nothing else.
- Chamber air at 41°F or less, read twice a day, with humidity and airflow in the range your plan names.
- Tag every cut with its start date, and set a last day.
- Trim off all the dried surface with a sanitized knife. The trim is discarded.
- Write down what you'll do if the chamber warms, before it does.
- TaroStack records each cut as a lot with its dates. More below.
What the Food Code says
| Point | Where | What it says |
|---|---|---|
| Named processes | 3-502.11(A) to (F), (H) | Smoking for preservation, curing, additives or vinegar for preservation, reduced oxygen packaging, shellfish tanks, custom processing, sprouting |
| Everything else | 3-502.11(G) | Another method the regulatory authority determines requires a variance |
| What an applicant shows | Annex 3 on 3-502.11 | Scientific evidence or analysis of how the hazards will be addressed, with the variance request |
| Cold holding | 3-501.16(A)(2) | 41°F or less |
The Food Code is a model. Your state or county adopts its own version, and that version and your inspector have the last word. The paperwork is in HACCP variance form, and the named processes in special process HACCP plan.
The hazards, step by step
| Step | Hazard | Control |
|---|---|---|
| Receiving | Pathogens on raw beef | Approved source; 41°F or less; whole sub-primals |
| Loading the chamber | Bacteria and moisture from other foods | A chamber for aging only; cuts not touching; date tags |
| Aging | Growth if the chamber warms | Air at 41°F or less; humidity and airflow in range |
| Days | Spoilage past the plan's limit | A last day for every cut |
| Trimming | Surface growth carried inside | All crust off; sanitized knife and board; trim discarded |
| Cutting, holding | Growth | 41°F or less; dated |
| Cooking | Survival in a rare steak | Your code's cooking and advisory rules |
The chamber
The chamber is the critical control point. Beef is a food that needs temperature control, so the air stays at 41°F or less the whole time, the Food Code's cold holding limit. Humidity and airflow decide how the surface dries. The Food Code gives no numbers for them, so they come from the evidence you put in your variance request, and they belong in the plan as a range someone reads and writes down.
Use the chamber for aging only. A walk-in shared with produce and sauces brings their moisture and their bacteria to meat that will sit open for a month.
Days, and the trim
Every cut gets a tag with the day it went in. This shop's plan sets a last day of 45, which is its own number. The log is read against the tags daily, and a cut past its day comes out.
The crust is what grew and dried on the outside for weeks. It all comes off, with a knife and board that were cleaned and sanitized first and again between cuts. This shop discards the trim.
Four days of the log
| Day | Chamber air at 8:00 | Limit | OK? |
|---|---|---|---|
| Nov 18 | 36°F | 41°F or less | Yes |
| Nov 19 | 37°F | 41°F or less | Yes |
| Nov 20 | 45°F | 41°F or less | NO: act |
| Nov 21 | 36°F | 41°F or less | Yes |
On the 20th the fan motor had failed overnight. The last reading was 37°F at closing, eleven hours earlier, so nobody could say how long the chamber had been warm. This shop's plan gives four hours above 41°F before the beef is discarded, and without a time, all six cuts went. The motor was replaced and the chamber stayed empty until it had held 36°F for a day. A thermometer that records, or one that sends an alarm, would have told them how long.
This is general information, not legal advice. Writing a plan from the start is in how to write a HACCP plan. The shop's wider plan is in HACCP plan for butcher shop, and a log for the readings in temperature log template.
Get the worksheet
Download the dry-aged beef HACCP plan worksheet. Three sheets and a read-me: the hazard analysis from receiving to cooking, the plan with its chamber, trimming and days controls, and a monitoring log that marks a reading above 41°F. It's an ordinary Excel file with no macros, and it works in Google Sheets, LibreOffice and Numbers.
Where this stops working
Six cuts in a chamber fit on a clipboard. Twenty, started on eight different days from four deliveries, don't. Which ones reach their last day this week? Which came from the supplier's lot that the distributor just called about? And what did the six that were thrown away cost?
How TaroStack does it
TaroStack makes each cut a lot with its dates and its cost.
Receiving records each delivery as a lot, with the supplier's lot number and what you paid.
Each cut in the chamber is stock with a date. An alert comes before a date arrives.
Stock is held by location, so the chamber is its own place, separate from the walk-in.
Every adjustment carries a reason. Six cuts written off as "chamber failure" is a number, at cost.
One report for a supplier's lot: where its beef went, and what's left.
| The question | Clipboard | In TaroStack |
|---|---|---|
| Which cuts reach their last day this week | Read every tag | Stock by date |
| Which came from that supplier's lot | Unknown | The lot's stock |
| What the lost cuts cost | A guess | The write-off, at cost |
| What's in the chamber now | Open the door | Stock by location |
TaroStack isn't a thermometer, and it doesn't write your plan or your variance request. Lots, dates, locations and adjustments are on every plan, from $9.99 a month (50 items) or $39 a month (3,000 items). The first 14 days are free, with no credit card. If you'd like a hand setting up, ask, and we'll do it with you.
