Skip to content

Maple Syrup Production Process: Sap to Bottle

The maple syrup production process step by step: sap handling, the rule of 86, boiling, finishing at 7.5°F over boiling water, density, filtering, bottling.

By Koa Sterling. Product specialist at TaroStack and small business owner. Yes, I am a real human, and I actually sit in front of a computer and write these articles. Reviewed November 21, 2026 · 6 min read

Maple syrup has one ingredient and one process: sap, with most of its water boiled away. What makes it a craft is that the endpoint is narrow. Too thin and it can spoil. Too thick and it crystallizes in the jug. The whole process, from tree to bottle, is six steps: collect the sap and keep it cold, boil it down, finish it at the right temperature, check its density, filter it hot, and bottle it hot. Two numbers run through all of it. Sap is about 2% sugar and syrup about 66% to 67%, so it takes roughly 43 gallons of sap to make one of syrup. And syrup is done when it boils 7.5°F above the boiling point of water that day. Below is each step with what two university extension services say about it, a sugarhouse's boil log, and a sheet for your own.

The short version

  • Keep sap cold, below 40°F, and boil it soon. It spoils like milk.
  • Gallons of sap for a gallon of syrup = 86 ÷ the sap's sugar percent.
  • Syrup is finished at 7.5°F above the boiling point of water, about 219°F.
  • Check density with a hydrometer: at least 66 Brix, and 67 in some States.
  • Filter hot to take out sugar sand.
  • Bottle at 180°F to 190°F.
  • TaroStack records each boil as a batch and each bottling as a lot. More below.

The steps

Step What happens The number Source
Collect and hold Sap gathered daily, filtered, kept cold Below 40°F. Over 50°F it spoils fast UNH Extension
Estimate Sap needed for a gallon of syrup 86 ÷ sugar percent. At 2%, 43 gallons UNH Extension
Boil Water evaporated in a pan or evaporator, in a ventilated building Penn State Extension
Finish Boiled to the finishing point on a controlled heat source 7.5°F above the boiling point of water, about 219°F UNH Extension
Check density Measured with a syrup hydrometer At least 66 Brix (Penn State). 67 Brix at 60°F is standard in New Hampshire and Vermont (UNH) Both
Filter Through wool or synthetic felt, hot Removes sugar sand, also called niter Both
Bottle Into clean containers, hot 180°F to 190°F Penn State Extension

Why the boiling point of water. Water doesn't boil at 212°F everywhere or every day. It changes with altitude and weather. So the finishing temperature is set from a pot of boiling water that morning, plus 7.5°F.

Why density is checked as well. UNH Extension puts the two failures plainly: syrup that's too dense forms crystals at the bottom of the container, and syrup that isn't dense enough can spoil and develop mold. A thermometer gets you close. A hydrometer confirms it.

Filtering. Minerals in the sap come out of solution as it concentrates. Unfiltered syrup is gritty and cloudy. Penn State Extension describes paper prefilters ahead of a wool or synthetic felt filter, and a filter press for larger producers.

A boil log

Date Sap Sugar Expected Made Sap a gallon Water boiled at Finish at Density Lot
Mar 6 320 gal 2.1% 7.8 gal 7.6 gal 42.1 211.4°F 218.9°F 66.9 M-0306
Mar 9 410 gal 2.4% 11.4 gal 11.2 gal 36.6 211.8°F 219.3°F 67.0 M-0309
Mar 14 280 gal 1.8% 5.9 gal 5.6 gal 50.0 211.1°F 218.6°F 66.2 M-0314
Mar 20 350 gal 2.0% 8.1 gal 8.0 gal 43.8 211.6°F 219.1°F 67.1 M-0320

The sugarhouse is made up. The log does three things.

It shows the sap changing. On March 9 the sap was 2.4% and a gallon of syrup took 36.6 gallons. On the 14th it was 1.8% and took 50. Same trees, five days apart. That's fuel and hours, and it's why the sugar is measured at every boil.

It checks the boil. Expected syrup is sap × sugar ÷ 86. Made is what went into containers. A gap much wider than usual means sap or syrup went somewhere: a boil-over, a leak, a scorched pan.

It flags the light one. M-0314 finished at 66.2 Brix. In a State whose standard is 67, that batch goes back on the finisher. Bottled as it is, it's the jug that molds in a pantry in June.

Grades, labels and rules

Penn State Extension says syrup sold has to conform to USDA grade standards, and that the legal definition of maple syrup includes a sugar content of at least 66 Brix. Your State sets its own density standard, license and label rules: ask your department of agriculture before you sell. Licensing is in maple syrup license, and how long syrup keeps in maple syrup shelf life. This is general information, not legal advice.

The numbers for the business are in maple syrup business plan and how to price maple syrup.

Get the boil log

Download the maple boil log. One sheet and a read-me: type the sap boiled, its sugar and the day's boiling point of water, and it works out the syrup to expect, the finishing temperature and the sap each gallon took, with columns for density, bottling temperature and lot. It's an ordinary Excel file with no macros, and it works in Google Sheets, LibreOffice and Numbers.

Where this stops working

By April there are thirty boils, drawn off into barrels, blended and bottled across May in three sizes. A customer writes in June about a quart that molded. Which boil was in that quart? What did it finish at? Which other jugs came from the same barrel, and which shops have them? The boil log has the density. The barrel, the bottling day and the deliveries are three other pieces of paper.

How TaroStack does it

TaroStack follows the syrup from the boil to the shop.

Each boil is a batch, with your checks as fields on its record: sap sugar, finishing temperature, density.

Each barrel and each bottling is a lot. A bottling takes syrup from a barrel's lot and jugs, caps and labels from stock, and notes which lots it used, automatically.

Lot labels print with the code, and stock is held by lot and location.

What ships is recorded by lot, so one report shows which shops got a bottling and what's left. Starting a recall holds it.

The customer's letter Three pieces of paper In TaroStack
Which boil was in that quart Guess from the dates The lots on the bottling
What it finished at The boil log A field on the batch
Which other jugs came from that barrel Unknown The barrel's lot
Which shops have them Invoices One report

TaroStack doesn't read a hydrometer or grade syrup. Recipes, batches, lots and recalls are on every plan, from $9.99 a month (5 recipes) or $39 a month (50 recipes). The first 14 days are free, with no credit card. If you'd like a hand setting up, ask, and we'll do it with you.

Questions people also ask

How many gallons of sap does it take to make a gallon of maple syrup?

Divide 86 by the sap's sugar percent. At 2% sugar that's 43 gallons. At 3% it's about 29.

What temperature is maple syrup done?

When it boils at 7.5°F above the boiling point of water that day, which is about 219°F. Check the density with a hydrometer as well.

What Brix should maple syrup be?

Penn State Extension gives at least 66 Brix. New Hampshire's and Vermont's standard is 67 Brix at 60°F. Check your own State's.

Sources

  1. University of New Hampshire Extension, Maple Sugaring: Tips for Beginners and Backyard Maple Sugar Producers (sap handling, the rule of 86, finishing temperature, density, filtering) · read November 21, 2026
  2. Penn State Extension, Maple Syrup Production (sugar content of at least 66 Brix, filtering, bottling at 180 to 190°F, grades) · read November 21, 2026

We use AI to help with the research for these articles. Every one is read, checked against its sources and edited by Koa before it's published. Spot a mistake? Tell us and we'll fix it and say so. How we write these.

Let’s get your stack in order.

Get TaroStack

Sign up now for your free 14 day trial. No credit card required.